URB24_YMD-15WR3 URB2409YMD-15WR3 --EngrWorld

Project name	Qualification	Unit	Notes
Working enviroment temperature	-40—+85	℃
Storage temperture	-40—+125 ℃	℃
Relative humidity	5—95	%
Heat dissipation mode	natural cooling
Atmospheric pressure	80—106 Kpa	Kpa
Vibrate	10-55Hz,10G,30Min.alongx,YandZ

Input Characteristics

Item	Working conditions		Min.	Typ.	Max.	Unit
Input current (full load/no load)	24VDC Input Series	3.3V	-	625/30	640/50	mA
		5V	-	694/30	710/50
		12V	-	694/69	710/35
		15V	-	687/69	703/15
		24V	-	687/10	703/20
		±5V	-	718/25	735/35
		±12V	-	686/1.5	702/2
		±15V	-	686/1.5	702/2
		±24V	-
	48VDC Input Series	3.3V	-	313/15	320/30
		5V	-	348/15	356/30
		12V	-	344/3	352/11
		15V	-	344/3	352/11
		24V	-	344/4	352/11
		±5V	-	359/1	368/1.5
		±12V	-	343/1	351/1.5
		±15V	-	343/1	351/1.5
		±24V	-	343/1	351/1.5
Reflection ripple current	Rated input voltage		-	30	-	mA
Impulse voltage (lsec.max）	24VDC Input Series		-0.7	--	50	VDC
Impulse voltage (lsec.max）	48VDC Input Series		-0.7	--	100
Start Voltage	24VDC Input Series		-	-	9
Start Voltage	48VDC Input Series		-	-	18
Input undervoltage protection	24VDC Input Series		5.5	6.5	-
Input undervoltage protection	48VDC Input Series		12	15.5	-
Input filter type		PI type
Hot plugged		Non-support

Output Characteristics

Project name	Working and testing condition	+Vo1			-Vo2
		Min.	Typ.	Max.	Min.	Typ.	Max.
Output load	load percentage	0%	-	100%	0%	-	100%
Output voltage accuracy		-	±1.0%	±2.0%	-	±2.0%	±3.0%
Linear adjustment rate	input voltage range	-	±0.2%	±0.5%	-	±1.5%	±2%
Load adjustment rate	20%-100% rated load, balanced load	-	±0.5%	±1.0%	-	±4.0%	±5.0%
Ripple & Noise	Pure resistive load,20MHz broadband, peak to peak, 5%-100% load	-	50mVp-p	80mVp-p	-	50mVp-p	80mVp-p
Start time delay		-	1ms	-	-	1ms	-
Input vlotage adjustment	input voltage range	-	no adjustment	-	-	no adjustment	-
Dynamic response step deviation	25% nominal load step	-	±3.0%	±5.0%	-	±3.0%	±5.0%
Dynamic response recovery time	25% nominal load step	-	300μs	500μs	-	300μs	500μs
Output overvoltage protection	full voltage input range	110%Vo	-	160%Vo
Output overcurrent protection	full voltage input range	110%lo	150%lo	200%lo
Output short circuit protection	full voltage input range			sustainable, self-recovery

Note:

(1) For product model with output voltage ±5VDC or ±9VDC , the maximum output voltage accuracy is ±5% under 0% - 5% load condition

(2) When tested according to the 0%-00% load working condition, the load adjustment rate is ±5%

(3) 0%-5% load ripple & noise less than or equal to 5% Vo. Ripple and noise test method, Twisted pair test method, can add capacitive load at the output to reduce light load ripple

Typical Application Circuits

EMC parameter recommendation

Component No.	24V input	48V input
Fuse	Follow up on customer needs and connect corresponding fuses
MOV1/Varistor	14D560K	14D101K
ldm1/Common mode inductance	10mH	15mH
CO,C1 Ceramic capacitors	1uF/50V	1uF/100V
E1,E2 Electrolytic capacitor	100uF/50V	100uF/100V
LDM2/Differential mode inductance	1nF/250Vac

Notes：

* Fuses and varistors are basic parts of protection circuits (required).

* If the certification is required, the safety capacitor and common mode inductance cannot be omitted.

Output filtering

QQ_1727169617223

For usual requirements of ripple and noise, the peripheral recommendation is only C2; For strict requirements of ripple and noise, the above circuit is recommended. Notes:

(1) C2, C3 use high frequency low resistance electrolytic capacitor, and the total capacity can not exceed the maximum capacitive load indicated in the manual, otherwise the module will not start normally. (2) When the capacitive load is used, the minimum load of 3% must be guaranteed, otherwise the module output will be abnormal.

Component No.	3.3V output	±5V or 5V output	±9/±12V or 9V/1V output	±15 or 15V output	±24 or 24V output
LDM3/Common mode inductance	0.47uH	1uH	2.2uH	2.2uH	4.7uH
LDM4/Common mode inductance	0.47uH	1uH	2.2uH	2.2uH	4.7uH
LDM5/Common mode inductance	-	1uH	2.2uH	2.2uH	4.7uH
C2,C3 Electrolytic capacitor	220uF	220uF	100uF	100uF	68uF
C5,C6 Electrolytic capacitor	220uF	220uF	100uF	100uF	68uF
C4 Ceramic capacitors	1uF/50V

Dimension and Weight

dimension 拷贝

Single(S)	1	2	3	4	5	6
	-VIN	+VIN	+VO	NP	GND	CTRL
	Input negative	Input positive	Output positive	----	Output positive	remote terminal
Dual(D)	-VIN	+VIN	+VO1	COM	-VO2	CTRL
Dual(D)	Input negative	Input positive	Output positive	common terminal	output negative2	remote terminal

	类型	描述
	产品类型	DC-DC模块
	制造商	Shenzhen Hi-Link
	厂牌	Hi-Link
	封装/性能	DIP Package
	功能类型	DC-DC Isolated Power Module
	转换效率	85%~90%
	工作电压（Vin)	24VDC
	输出电压精度	±1.0%~±2.0%
	输出功率	15W
	静态电流（lq)	1mA
	开关频率	250kHz
	纹波噪声	50~80mVp-p
	工作温度	-40℃ ~ +85℃

显示相似产品 ( 0 )

购物指南

阶梯价格

梯度	单价	总价
1+	$4.63	$4.63

库存总量

中国大陆仓库
11000

购买数量

起订量:1 增量:1

总价：

加入心愿单

分享链接

服务申明

快递

支持七天无理由退货

如果快递丢失，支持退货

如果快递损坏，支持退货

支持90天内免费换货

安全与隐私

安全付款:未经您的同意，我们不会与任何第三方分享您的个人信息。

安全的个人资料:我们保护您的隐私，确保您的个人资料安全可靠。

支付安全

与受欢迎的支付合作伙伴合作，您的个人信息是安全的。

HI-LINK (HK)CO.. LIMITED

公司

支持

联系我们